一、适用

莱卡布,牛仔布(涂层布，压光布除外)、尼龙布、TPU、PU皮革，及一些高弹性面料等。

二、性能指标

◇外观及组成：乳白色粘稠状体，聚氨酯聚合物

◇布氏粘度：140000~160000CPS

◇PH值：7.0-8.0

◇离子类型：阴离子

◇固体含量：65%±1

三、特性

立体感强，触边性好，高附着力，高亮光，高弹性，手感超柔软，抗回粘性能优。表面光滑，牢度超强。耐高温水洗、雪花洗、漂洗、酵素洗、酸洗、耐高温蒸煮。厚板印花后达到类似硅胶的效果（避免45℃以上高温或—35℃以下低温）优越的低温耐折。耐黄变.常温下保存12个月，属于高端环保型浆料。

四、操作应用

◇ 本产品一般使用80目120目网布，根据图案的不同丝网一定要绷紧，这一点相当关键。

◇ 为了保证印制效果，一般不要制作太厚网版，根据厚度不同需要印5—8次，在使用厚网版印刷时印完第一次需待底层干透后再进行第二次印刷，一般印刷3—5次就能达到2-3毫米以上的高度。

◇ 本产品不易塞网，过稠时可加入适当水浆搅拌均匀进行稀释。

◇ 在自然风干48小时后，再过温150度8-15秒，过温时尽量将面料过反面。

◇ 使用时加入1%-2%交联剂。（加好助剂的浆料要在3~6小时内用完）。

五、注意事项

◇ 自然干燥时间与气温和空气湿度有关。

◇ 调色可根据客户需要颜色的深浅来调入色种的分量，颜色调入太多容易引起掉色现象，色种最好控制在5%之内。

◇ 如印容易掉色的深色布，需要测试颜色是否会升华到胶浆表面上，以减少不必要的损失。

◇ 使用本透明产品印花，要稍加白胶浆掺和进行调色印花有利于在纺织品面料上印花着色度饱和，更好发挥透明浆的应用效果。

◇ 由于印花面料的多样化，和一些外在的不确定因素做大货之前先小样实验确定以后方可批量生产。未确定情况使用或操作不当引起的质量问题本公司概不负责。

Other detailed information

一．Substrates

Lycra, denim(coated fabric, press polishing fabric), nylon, TPU and PU leather.

二．Performance and indicators

Appearance and composition: white (clear)viscous body, polyester

Brinell viscosity:140000-160000CPS

PH value:7.0-8.0

Ionic:anion

Solid content:65%±1

三．Features

Good stereoscopic and edge,high adhesion,soft hand feel,excellent ability of anti- after tack. Stain finish,good fastness. Resistance to high-temperature ,snow,blench,enzyme,acid wash. As well as resistant to high-temperature steaming.(avoid temperature over 46℃ or below -35℃)and ultrow temperature folding.Resistance to yellowing,the shelf life is 12 months at room temperature,belongs to high-end environmental paste.

四．Operation application

This product uses 80-120mesh screen as usual. The crux is that according to different shape,the mesh screen must tighten.

In order to guarantee the printing effect,should not manufacture thick mesh screen. According to different thickness, it needs to print 6-8times.When using thick mesh screen print, what we should notice that it must be dry enough and then print in second time.Printing 3-5times can reach the height of2-3mm.

This product is not easy to plug mesh,you could add suitable water slurry and stir to dilute when it too thick.

After air dry naturally for 48 hours,and then over-temperature for 8-15seconds at 150℃.When over-temperature,it better to put fabric in opposite side.

You should add 1%-2%crosslinker when using the product.(The paste with auxiliaries ,you should run out within 3-6hours.)

五．Notes

The time of drying is related to humidity of the air.

When adjusting the color,the amount of pigment you should add according to the customer’s needs.If add too much color, it will lead to come off, the amount of pigment it better to add within 5%.

If print on dark fabric which is easy to come off, it better to make a test that color whether sublimate on the surface of paste, in order to reduce unnecessary financial losses.

Using this transparent product to print,add some white paste to print ,it could makes the textile surface looks more saturated and make the clear paste reach the best application effect.

Due to variety of printing fabrics and some uncertain factors outside , you should better make a test before in a batch production. Our company is not responsible for quality problem which caused under uncertain condition or operate incorrectly.