本公司经营烫画机、烤杯机、热转印设备及耗材,质量保证,欢迎咨询洽谈。
概述:
本机可以将任何彩色色标,人像照片,风景图案等烫印在帽子上,特别适用于广礼品,宣传画等.同时也可作为个性化礼品,兼艺术欣赏和实用性于一体.
特点:
使用说明
注:为了安全起见,电源必需符合有保护接地线的单相3线电源
提起操作手柄,使机器成张开状。在工作平台上放上要烫印的物体,测试压力是否合适,如不合适,需调节压力旋钮。(顺时针旋转旋钮为加大压力,逆时针旋转为减小压力)
张开机器,取下待烫印物。(升温过程请不要将待烫印物放置在工作平台上,以免烤坏)
打开电源开关,温控仪开始自检,约10秒后自检完成并进入工作状态,此时才可设置工作参数,(第一次使用请设置好所需:温度、时间,详见后附仪表面板时间与温度操作说明)
设定好需要的温度、时间,机器开始升温加热(温度上升至200℃大约需要15分钟)
待机器达到所需温度时,将需要转印的帽子平铺放置在工作台面上,再叠要转印的图片,压下操作手柄,机器开始自动计时,达到设定的时间后,机器发出警示音,提起操作手把,速取出帽子,撕去底纸,完成一次操作。
保修:
感谢您选择我们公司的产品,您享有我司对本产品实行的一年免费保修服务。对于我司没有维修网点的地方或者国外,我们只能提供替换配件并通过远程协助来指导顾客自行维修;对于超过保修期的我们仍然提供技术支持与维修指导
属下例情况,我们可能酌情收取配件成本费:顾客未安要求或因操作、维护、运输不当而造成产品损坏或出现故障的;
This machine could transfer colorful photos,words on cap,suitable for producing gifts,decorations.
Specification:
1. Digital controller,more accurate
2. Swing-away design makes using more easy
3. Easy to adjust the pressure
Usage
1.Place printing material on working table,get right pressure you need
2.take out material
3.Turn on power,about 10 sec then you could set Controller to get right temp and time you need
4.Then the machine will heating up(200℃about 15 minutes)
5.After machine reach temp you set,then place cap on the working table flatly,place the photo you printing on cap,then press down the handle.When the machine reach the time you set,it will alarm,you could take out the cap and peel off the paper,then photo will transfer on the cap.
Attention
If the paper is cold peel,then you need to wait 15-20 sec and peel off paper.If it is hot peel,then you need to peel off paper at once after printing. (had better peel paper in diagonal line)
Successful printing needs right time,temp and pressure,You need to test printing to get right time and temp first
Problem and slove
出口免熏蒸木箱包装:
●Current voltage: 220V/ 110V
●Watts: 550W
●’The range of the temperature:0-399℃
●Wooden case packing: 54X32X86cm
●Working Table: 9.5cmx15cm
●Range of time: 0-999sec
●Actual weight: 40KG
Machine not working Check the power or Fuse inside
Heating board not working clock problem/solid relay system not working/heating board burn
Not alarm clock problem or time switch broken